|
Post by son7771 on Aug 2, 2010 11:36:38 GMT -5
Got married this weekend and had a cruise before the reception. The Ford didnt make it the radiator gave up the ghost halfway in!!! I always wantes a SIX PACK under the hood but I suspect that them on the hood is OK as well!!!! Uploaded with ImageShack.usUploaded with ImageShack.usUploaded with ImageShack.usHere is a pic of the cake I designed it was a joke because wife says I am married to my car!!! Uploaded with ImageShack.us
|
|
|
Post by son7771 on Jul 23, 2010 22:50:55 GMT -5
got mine at napa easy install Cant remember part number but if you bring them in they look in a book and found what i needed. I got the reverse ones too.
|
|
|
Post by son7771 on Jul 5, 2010 10:44:08 GMT -5
I have a edelbrock 750 and I have vacuum hooked up on drivers side of carburetor. I had some problems the last couple of weeks that had me tearing top end apart but never found any real answers. I did find that my pickup on electronic distributer was way out of spec. I think I have this figured out but now am unsure what side vacuum advance hooks up as web has both sides!!!! Thanks This is for a 400
|
|
|
Post by son7771 on Apr 29, 2010 7:03:14 GMT -5
Take carpet off your hump and you can see where hole is cut. As far as mounting the consule mounts you need measurement from donor car. there is a kit you can buy on ebay or elswhere for the mounting
|
|
|
Post by son7771 on Apr 27, 2010 20:53:26 GMT -5
440 source has everyting you want and if you call them they give great tech advice. Qaulity parts and nice peoples to boot!!! www.440source.com/ I got there heads and arp bolts gaskets and sparkplugs less then what edelbrock heads alone cost. I was going to stroke out my motor with there kits (cheapest I have found) but I found a fresh rebuild and put a cam and the heads in it and what a differnce it made!!!!
|
|
|
Post by son7771 on Apr 20, 2010 8:44:27 GMT -5
It is not that hard to paint and with a little practice (cheap paint, old fender, door) you could get it right and do just as good a job as them!!! You can get the spray guns at harbor frieght cheap. My dad uses these guns and it comes out just as nice as my 300$ gun. Go to a paint shop and see if the got some screw up paint in single stage and give it a try!! I am sure there are some tutorials on the web with a google search you could find them.
|
|
|
Post by son7771 on Apr 18, 2010 20:24:43 GMT -5
the saying goes "You get what you Pay for"
|
|
|
Post by son7771 on Apr 7, 2010 22:39:43 GMT -5
All the controls are on the seat. Bring a battery for a cordless drill and some jumper wires for red and black wires if car doesnt have power. You need to move seats foward and back to get bolts out
|
|
|
Post by son7771 on Apr 6, 2010 6:56:15 GMT -5
Well this would depend on what size rims 14,15 ect and then on width of rim as well. Here is what i went with on my 72 front 15X7 5X4.50BC 4Back Space 245-60-15 rear 15X8 5X4.50BC 4 1/2 back space 275-60-15
|
|
|
Post by son7771 on Apr 5, 2010 7:14:45 GMT -5
October of 2008. Had it done by May of 2009 but still tinkering with it!!!!
|
|